Are you struggling to find the right learning materials to prepare for the Implementing Cisco Enterprise Advanced Routing and Services (ENARSI) 300-410 exam? Maybe the 300-410 enarsi dumps information you are looking for does not satisfy you?
Exampass.net helps you. Share the latest and truest 300-410 enarsi exam dumps of 12 practice questions in online test and PDF mode, welcome to learn.
If you feel good about learning, you can also visit here for a full Cisco CCNP 300-410 enarsi dumps https://www.pass4itsure.com/300-410.html Boost your CCNP 300-410 exam.
As we all know, a good 300-410 enarsi dumps can help you save time and effort to quickly study through the Cisco CCNP enarsi exam.
What is the best? CCNP 300-410 enarsi dumps
First of all, you must ensure that the dumps are real and updated, and that outdated information is harmful to the exam. Secondly, the way must be more diverse, and a single boring learning method is difficult to adhere to.
These Required Pass4itSure dumps can do it, or try it.
Download PDF file: (CCNP 300-410 enarsi dumps pdf free download)
[Google Drive] free share 300-410 enarsi pdf https://drive.google.com/file/d/1CiJknYcuOKQR2_S0p0GM-ZsbD9fxWFfJ/view?usp=sharing
Go in Cisco 300-410 online test questions 1-12
At the end of the question, the answer is tested independently, and then the correct answer is checked to test yourself more realistically.
1. Refer to the exhibit.
An engineer configures the router 10.1.100.10 for EIGRP autosummarization so that R1 should receive the summary route of 10.0.0.0/8. However, R1 receives more specific /24 routes. Which action resolves this issue?
A. Router R1 should configure ip summary address eigrp (AS number) 10.0.0.0 255.0.0.0 for the R1 Fast Ethernet 0/0 connected interface.
B. Router R1 should configure ip route 10.0.0.0 255.0.0.0 null 0 for the routes that are received on R1.
C. Router 10.1.100.10 should configure ip route 10.0.0.0 255.0.0.0 null 0 for the routes that are summarized toward R1.
D. Router 10.1.100.10 should configure ip summary address eigrp (AS number) 10.0.0.0 255.0.0.0 for the R1 Fast Ethernet 0/0 connected interface.
2. Refer to the exhibit.
Redistribution is enabled between the routing protocols, and nowPC2 PC3, and PC4 cannot reach PC1. What are the two solutions to fix the problem? (Choose two.)
A. Filter RIP routes back into RIP when redistributing into RIP in R2
B. Filter OSPF routes into RIP from EIGRP when redistributing into RIP in R2
C. Filter all routes except RIP routes when redistributing into EIGRP in R2.
D. Filter RIP AND OSPF routes back into OSPF from EIGRP when redistributing into OSPF in R2
E. Filter all routes except EIGRP routes when redistributing into OSPF in R3.
Even PC2 cannot reach PC1 so there is something wrong with RIP redistribution in R2. Because RIP has higher Administrative Distance (AD) value than OSPF and EIGRP so it will be looped when doing mutual redistribution.
3. Refer to the exhibit.
Which action restores the routes from neighbors while still filtering 1.1.1.0/24?
A. Add a second line in the access list to permit any.
B. Modify the route map to permit the access list instead of deny it
C. Modify the access list to deny insteac of permit it.
D. Add a second sequence in the route map permit 20
We need to add a second sequence with the “route-map FILTER1 permit 20” (with no match conditions) so that all other conditions are permitted.
4. How is VPN routing information distributed in an MPLS network?
A. It is controlled through the use of RD.
B. The top level of the customer data packet directs it to the correct CE device.
C. It is established using VPN IPsec peers.
D. It is controlled using of VPN target communities.
5.
Refer to the exhibits. A user on the 192.168.1.0/24 network can successfully ping 192.168.3.1, but the administrator cannot ping 192.168.3.1 from the LA router. Which set of configurations fixes the issue?
A. Option A
B. Option B
C. Option C
D. Option D
6. Refer to the exhibit.
R2 has two paths to reach 192.168.13.0/24. but traffic is sent only through R3. Which action allows traffic to use both paths?
A. Configure the bandwidth 2000 command under interface FastEthernet0/0 on R2.
B. Configure the variance 4 command under the EIGRP process on R2.
C. Configure the delay 1 command under interface FastEthernet0/0 on R2.
D. Configure the variance 2 command under the EIGRP process on R2
From the output of the “show ip eigrp topology …” command, we notice network 192.168.13.0/24 was learned via two routes:+ From 192.168.23.3 (R3) with FD = 1075200 and AD = 281600+ From 192.168.12.1 (R1) with FD = 2611200 and AD = 281600
From the output of the “show ip route …” command, we learned that the best (and chosen) path is via 192.168.23.3 (R3).
To use both paths (called unequal cost load balancing) with EIGRP, the second path via R1 must satisfy the feasibility condition. The feasibility condition states that, theAdvertised Distance (AD) of a route must be lower than the feasible distance of the current successor route.
In this case, the second path satisfies the feasible condition as its AD (281600) is smaller than the FD (1075200) of the best path. Therefore we can configure loadbalancing with “variance” command.
In other words, EIGRP will install all paths with metric metric / best_metric = 2611200 / 1075200 =2.4. So with a variance greater than 2 (and must be an integer), we can load balance traffic to network 192.168.13.0/24.
7. R2 has a locally originated prefix 192.168.130.0/24 and has these configurations: What is the result when the route-map OUT command is applied toward an eBGP neighbor R1 (1.1.1.1) by using the neighbor 1.1.1.1 route-map OUT out command?
A. R1 sees 192.168.130.0/24 as two AS hops away instead of one AS hop away.
B. R1 does not accept any routes other than 192.168.130.0/24
C. R1 does not forward traffic that is destined for 192.168.30.0/24
D. Network 192.168.130.0/24 is not allowed in the R1 table
8. What is the role of a route distinguisher via a VRF-Lite setup implementation?
A. It extends the IP address to identify which VFP instance it belongs to.
B. It manages the import and export of routes berween two or more VRF instances
C. It enables multicast distribution for VRF-Lite setups to enhance EGP routing protocol capabilities
D. It enables multicast distribution for VRF-Lite setups to enhance IGP routing protocol capabilities
9. A network administrator is troubleshooting a high utilization issue on the route processor of a router that was reported by NMS.
The administrator logged into the router to check the control plane policing and observed that the BGP process is dropping a high number of routing packets and causing thousands of routes to recalculate frequently. Which solution resolves this issue?
A. Police the pir for BGP, conform action set-prec-transmit, and exceed action set-clp-transmit.
B. Police the cir for BGP, conform action transmit, and exceed action transmit
C. Shape the cir for BGP, conform-action transmit and exceed action transmit
D. Shape the pir for BGP, conform-action set-prec-transmit, and exceed action set-frde-transmit.
10. Refer to the exhibit.
A network administrator has developed a Python script on the local Linux machine and is trying to transfer it to the router. However, the transfer fails. Which action resolves this issue?
A. The SSH access must be allowed on the VTY lines using the transport input ssh command.
B. The SSH service must be enabled with the crypto key generate rsa command
C. The SCP service must be enabled with the ip sop server enable command.
D. The Python interpreter must first be enabled with the guestshell enable command.
11. A network engineer is configuring a DHCP server to support a specialized application. Which additional DHCP feature must be enabled to support the delivery of various additional parameters to DHCP clients?
A. modules
B. vendor extensions
C. options
D. Scopes
12. Refer to Exhibit.
Which two configurations allow clients to get dynamic ip addresses assigned?
A. Configure access-list 100 permit udp any any eq 61 as the first line
B. Configure access-list 100 permit udp any any eq 86 as the first line
C. Configure access-list 100 permit udp any any eq 68 as the first line
D. Configure access-list 100 permit udp any any eq 69 as the first line
E. Configure access-list 100 permit udp any any eq 67 as the first line
A DHCP server that receives a DHCPDISCOVER message may respond with a DHCPOFFER message on UDP port= 68 (BootP client).…
In the event that the DHCP server is not on the local subnet, the DHCP server will send the DHCPOFFER, as a unicast packet, on UDP port 67, back to the DHCP/BootPRelay Agent from which the DHCPDISCOVER came.
Correct answer posted
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 |
| D | AB | D | D | D | B | A | A | B | C | C | CE |
Summary:
The latest free 300-410 dumps 12 Q&As and free 300-410 PDFs have been shared above, these are from real and updated dumps, safe and trustworthy. Helps you easily pass the Simplifying Cisco Enterprise Advanced Routing and Services (ENARSI) exam.
Finally, under emphasis, get the complete 300-410 enarsi dumps to help you pass the exam https://www.pass4itsure.com/300-410.html PDF+VCE multi-mode to help you learn happily.
