What are the tools available for performing 300-115 dumps? Implementing Cisco IP Switched Networks (SWITCH 300-115) is a qualifying exam for the Cisco CCNP Routing and Switching, CCDP certifications. The CCDP pass4itsure 300-115 dumps pdf exam certifies the switching knowledge and skills of successful candidates. They are certified in de that use pass4itsure team Implementing Cisco IP Switched Networks course. After taking this course, you will be prepared for certification exam, which is taken at pass4itsure testing center. The user must complete Cisco CCNP Routing and Switching, CCDP prior to taking this 300-115 dumps course. Users will receive certificate of completion upon passing the course with an 80% or better.
Exam Code: 300-115
Exam Name: Implementing Cisco IP Switched Networks
Q&As: 647
Pass4itsure 300-115 Dumps Related Exams
- 642-871 Designing Cisco network Service Architectures (ARCH)
- 642-873 Designing Cisco network Service Architectures (ARCH)
- 642-874 Designing Cisco Network Service Architectures
- 300-101 Implementing Cisco IP Routing
- 300-115 Implementing Cisco IP Switched Networks
- 300-320 Designing Cisco Network Service Architectures
Pass4itsure 300-115 Dumps Related Certifications
- Wireless LAN
- WAASSE
- Wireless BYOD Specialist
- VPN and Security
- Unified Communications
- Substation Automation
- TelePresence Video
- Storage Networking
The Implementing Cisco IP Switched Networks (300-115 SWITCH) version is a 2-hour test with 30-40 questions questions that validate professionals who have the expertise in planning, configuring, and verifying the implementation of complex enterprise switching solutions that use the Cisco Enterprise Campus Architecture.
PASS4ITSURE LATEST AND MOST ACCURATE Cisco 300-115 DUMPS DUMPS EXAM Q&AS(1-27)
QUESTION 1
Drag Drop
Select and Place:
300-115 exam Correct Answer:
Explanation
Explanation/Reference:
QUESTION 2
Drag Drop
Select and Place:
Correct Answer:
Explanation
Explanation/Reference:
QUESTION 3
Drag and Drop
Select and Place:
300-115 dumps Correct Answer:
Explanation
Explanation/Reference:
QUESTION 4
Drag and Drop
Select and Place:
Correct Answer:
Explanation
Explanation/Reference:
QUESTION 5
Drag and Drop
Select and Place:
300-115 pdf Correct Answer:
Explanation
Explanation/Reference:
QUESTION 6
Drag and Drop
Drag the attributes on the left to the types of VLAN designs that they describe on the right.
Select and Place:
Correct Answer:
Explanation
Explanation/Reference:
QUESTION 7
Drag and Drop
Select and Place:
300-115 vce Correct Answer:
Explanation
Explanation/Reference:
QUESTION 8
Drag and Drop
Select and Place:
Correct Answer:
Explanation
Explanation/Reference:
QUESTION 9
Drag and Drop
Select and Place:
300-115 exam Correct Answer:
Explanation
Explanation/Reference:
QUESTION 10
Drag and Drop
Select and Place:
Correct Answer:
Explanation
Explanation/Reference:
QUESTION 11
Drag and Drop
Select and Place:
300-115 dumps Correct Answer:
Explanation
Explanation/Reference:
QUESTION 12
Drag and Drop
Match the HSRP states on the left with the correct definition on the right.
Select and Place:
Correct Answer:
Explanation
Explanation/Reference:
QUESTION 13
Drag and Drop
Select and Place:
300-115 pdf Correct Answer:
Explanation
Explanation/Reference:
QUESTION 14
Drag and Drop
PortFast / BPDU Guard / BPDU Filter.
Select and Place:
Correct Answer:
Explanation
Explanation/Reference:
QUESTION 15
Drag and Drop
PVST+ / Rapid PVST+ / MSTP
Select and Place:
300-115 vce Correct Answer:
Explanation
Explanation/Reference:
QUESTION 16
Drag and Drop
STP Timers
Select and Place:
Correct Answer:
Explanation
Explanation/Reference:
QUESTION 17
Drag and Drop
Port Cost / Switch Port Priority / Port Priority
Select and Place:
300-115 exam Correct Answer:
Explanation
Explanation/Reference:
QUESTION 18
Drag and Drop
Guard Root / Guard Loop
Select and Place:
Correct Answer:
Explanation
Explanation/Reference:
QUESTION 19
Drag and Drop
STP Timer Delay
Select and Place:
300-115 dumps Correct Answer:
Explanation
Explanation/Reference:
QUESTION 20
Drag and Drop
LLDP-TLV
Select and Place:
Correct Answer:
Explanation
Explanation/Reference:
QUESTION 21
Drag and Drop
Drag and drop the characteristic from the left to the matching Layer 2 protocol on the right.
Select and Place:
300-115 pdf Correct Answer:
Explanation
Explanation/Reference:
QUESTION 22
Lab Simulation – AAA dot1x
SWITCH.com is an IT company that has an existing enterprise network comprised of two layer 2 only switches; DSW1 and ASW1. The topology diagram indicates their layer 2 mapping. VLAN 20 is a new VLAN that will be used to provide the shipping personnel access to the server. Corporate polices do not allow layer 3 functionality to be enabled on the switches.
For security reasons, it is necessary to restrict access to VLAN 20 in the following manner:
– Users connecting to VLAN 20 via portfO/1 on ASW1 must be authenticated before they are given access to the network.
Authentication is to be done via a Radius server:
– Radius server host: 172.120.40.46
– Radius key: rad123
– Authentication should be implemented as close to the host as possible.
– Devices on VLAN 20 are restricted to the subnet of 172.120.40.0/24.
– Packets from devices in the subnet of 172.120.40.0/24 should be allowed on VLAN 20.
– Packets from devices in any other address range should be dropped on VLAN 20.
– Filtering should be implemented as close to the serverfarm as possible
The Radius server and application servers will be installed at a future date. You have been tasked with implementing the above access control as a pre-condition to installing the servers. You must use the
available IOS switch features.
A. See the explanation
Correct Answer: A
Explanation
Explanation/Reference:
1. Verification of Pre-configuration:
a. Check that the denoted vlan [vlan20] is created in both switches and ports [fa0/1 of ASW1] are assigned.
b. Take down the radius-server ip [172.120.39.46] and the key [rad123].
c. Take down the IP range [172.120.40.0/24] to be allowed the given vlan [vlan20]
2. Configure the Port based authentication on ASW1:
Enable AAA on the switch:
ASW1> enable
ASW1# conf t
ASW1(config)# aaa new-model
The new-model keyword refers to the use of method lists, by which authentication methods and sources
can be grouped or organized. Define the server along with its secret shared password:
ASW1(config)# aaa authentication dot1x default group radius
ASW1(config)# radius-server host 172.120.39.46 key rad123
This command causes the RADIUS server defined on the switch to be used for 802.1x authentication.
Enable 802.1x on the switch:
ASW1(config)# dot1x system-auth-control
Configure Fa0/1 to use 802.1x:
ASW1(config)# interface fastEthernet 0/1
ASW1(config-if)# switchport mode access
ASW1(config-if)# dot1x port-control auto
Notice that the word “auto” will force connected PC to authenticate through the 802.1x exchange.
ASW1(config-if)# exit
ASW1# copy running-config startup-config
3. Filter the traffic and create vlan access-map to restrict the traffic only for a range on DSW1 Define an access-list:
DSW1> enable
DSW1# conf t
(syntax: ip access-list {standard | extended} acl-name)
DSW1(config)# ip access-list standard 10
DSW1(config-ext-nacl)# permit 172.120.40.0 0.0.0.255
DSW1(config-ext-nacl)# exit
Define an access-map which uses the access-list above:
(syntax: vlan access-map map_name [0-65535] )
DSW1(config)# vlan access-map MYACCMAP 10
(syntax: match ip address {acl_number | acl_name})
DSW1(config-access-map)# match ip address 10
DSW1(config-access-map)# action forward
DSW1(config-access-map)# exit
DSW1(config)# vlan access-map MYACCMAP 20
(drop other networks)
DSW1(config-access-map)# action drop
DSW1(config-access-map)# exit
Apply a vlan-map into a vlan:
(syntax: vlan filter mapname vlan-list list)
DSW1(config)# vlan filter MYACCMAP vlan-list 20
DSW1# copy running-config startup-config
4. Note:
It is not possible to verify the configuration in this lab. All we have do the correct configurations. Most of the exam takers report that ” copy running-config startup- config” is not working. It does not a matter.
Do not try unwanted/wrong commands in the consoles. They are not real switches.
QUESTION 23
You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration.
You are connecting the New_Switch to the LAN topology; the switch has been partially configured and you need to complete the rest of configuration to enable PC1 communication with PC2. Which of the configuration is correct?
A. Option A
B. Option B
C. Option C
D. Option D
E. Option E
300-115 vce Correct Answer: D
Explanation
Explanation/Reference:
Within any VTP, the VTP domain name must match. So, step one is to find the correct VTP name on the other switches. Logging in to SW1 and using the “show vtp status” command we see this:
So we know that the VTP domain must be CCNP. This leaves only choice D and E. We also see from the topology diagram that eth 0/0 of the new switch connects to a PC in VLNA 100, so we know that this port must be an access port in
VLAN 100, leaving only choice D as correct. Note that the VTP versions supported in this network are 1, 2, 3 so either VTP version 2 or 3 can be configured on the new switch.
QUESTION 24
You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration.
Refer to the configuration. For which configured VLAN are untagged frames sent over trunk between SW1 and SW2?
A. VLAN1
B. VLAN 99
C. VLAN 999
D. VLAN 40
E. VLAN 50
F. VLAN 200
G. VLAN 300
300-115 exam Correct Answer: B
Explanation
Explanation/Reference:
The native VLAN is used for untagged frames sent along a trunk. By issuing the “show interface trunk” command on SW1 and SW2 we see the native VLAN is 99.
QUESTION 25
You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration.
You are adding new VLANs. VLAN500 and VLAN600 to the topology in such way that you need to configure SW1 as primary root for VLAN 500 and secondary for VLAN 600 and SW2 as primary root for VLAN 600 and secondary for VLAN 500. Which configuration step is valid?
A. Configure VLAN 500 & VLAN 600 on both SW1 & SW2
B. Configure VLAN 500 and VLAN 600 on SW1 only
C. Configure VLAN 500 and VLAN 600 on SW2 only
D. Configure VLAN 500 and VLAN 600 on SW1 ,SW2 and SW4
E. On SW2; configure vtp mode as off and configure VLAN 500 and VLAN 600; configure back to vtp server mode.
Correct Answer: A
Explanation
Explanation/Reference:
By issuing the “show vtp status command on SW2, SW2, and SW4 we see that both SW1 and SW2 are operating in VTP server mode, but SW4 is a client, so we will need to add both VLANs to SW1 and SW2.
QUESTION 26
You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration.
Examine the VTP configuration. You are required to configure private VLANs for a new server deployment connecting to the SW4 switch. Which of the following configuration steps will allow creating private VLANs?
A. Disable VTP pruning on SW1 only
B. Disable VTP pruning on SW2 only
C. Disable VTP pruning on SW4 only
D. Disable VTP pruning on SW2, SW4 and New_Switch
E. Disable VTP pruning on New_Switch and SW4 only.
300-115 dumps Correct Answer: C
Explanation
Explanation/Reference:
To create private VLANs, you will need to only disable pruning on the switch that contains the private VLANs. In this case, only SW4 will connect to servers in a private VLAN.
QUESTION 27
Lab Simulation – MLS and EIGRP
You have been tasked with configuring multilayer SwitchC, which has a partial configuration and has been attached to RouterC as shown in the topology diagram. You need to configure SwitchC so that Hosts H1 and H2 can successfully ping
the server S1. Also SwitchC needs to be able to ping server S1. Due to administrative restrictions and requirements you should not add/delete vlans or create trunk links. Company policies forbid the use of static or default routing. All routes must be learned via EIGRP 65010 routing protocol. You do not have access to RouteC. RouterC is correctly configured. No trunking has been configured on RouterC. Routed interfaces should use the lowest host on a subnet when possible. The following subnets are available to implement this solution:
– 10.10.10.0/24
– 190.200.250.32/27
– 190.200.250.64/27
Hosts H1 and H2 are configured with the correct IP address and default gateway.
SwitchC uses Cisco as the enable password.
Routing must only be enabled for the specific subnets shown in the diagram. Note: Due to administrative restrictions and requirements you should not add or delete VLANs, changes VLAN port assignments or create trunks. Company policies forbid the use of static or default routing. All routes must be learned via the EIGRP routing protocol.
A. See the explanation
300-115 pdf Correct Answer: A
Explanation
Explanation/Reference:
In real life, there are two ways to configure interVLAN routing in this case:
+ Use RouterC as a “router on a stick” and SwitchC as a pure Layer2 switch. Trunking must be established between RouterC and SwitchC. + Only use SwitchC for interVLAN routing without using RouterC, SwitchC should be configured as a Layer 3 switch (which supports ip routing function as a router). No trunking requires. The question clearly states “No trunking has been configured on RouterC” so RouterC does not contribute to interVLAN routing of hosts H1 & H2 -> SwitchC must be configured as a Layer 3 switch with SVIs for interVLAN routing. We should check the default gateways on H1 & H2. Click on H1 and H2 and type the “ipconfig” command to get their default gateways.
C:\>ipconfig
We will get the default gateways as follows:
Host1:
+ Default gateway: 190.200.250.33
Host2:
+ Default gateway: 190.200.250.65
Now we have enough information to configure SwitchC (notice the EIGRP AS in this case is 650)
Note: VLAN2 and VLAN3 were created and gi0/10, gi0/11 interfaces were configured as access ports so we don’t need to configure them in this sim.
SwitchC# configure terminal
SwitchC(config)# int gi0/1
-> without using this command, the simulator does not let you assign IP address on Gi0/1 interface.
SwitchC(config-if)#no switchport
->RouterC has used IP 10.10.10.1 so this is the lowest usable IP address.
SwitchC(config-if)# ip address 10.10.10.2 255.255.255.0
SwitchC(config-if)# no shutdown
SwitchC(config-if)# exit
SwitchC(config)# int vlan 2
SwitchC(config-if)# ip address 190.200.250.33 255.255.255.224
SwitchC(config-if)# no shutdown
SwitchC(config-if)# int vlan 3
SwitchC(config-if)# ip address 190.200.250.65 255.255.255.224
SwitchC(config-if)# no shutdown
SwitchC(config-if)#exit
(Notice: MLS will not work without this command)
SwitchC(config)# ip routing
SwitchC(config)# router eigrp 650
SwitchC(config-router)# network 10.10.10.0 0.0.0.255
SwitchC(config-router)# network 190.200.250.32 0.0.0.31
SwitchC(config-router)# network 190.200.250.64 0.0.0.31
NOTE: THE ROUTER IS CORRECTLY CONFIGURED, so you will not miss within it in the exam , also don’t modify/delete any port just do the above configuration. Also some reports said the “no auto-summary” command can’t be used in the
simulator, in fact it is not necessary because the network 190.200.0.0/16 is not used anywhere else in this topology.
In order to complete the lab , you should expect the ping to SERVER to succeed from the MLS , and from the PCs as well.
Also make sure you use the correct EIGRP AS number (in the configuration above it is 650 but it will change when you take the exam) but we are not allowed to access RouterC so the only way to find out the EIGRP AS is to look at the exhibit
above. If you use wrong AS number, no neighbor relationship is formed between RouterC and SwitchC.
In fact, we are pretty sure instead of using two commands “network 190.200.250.32 0.0.0.31” and “network 190.200.250.64 0.0.0.31” we can use one simple command “network 190.200.0.0” because it is the nature of distance vector routing
protocol like EIGRP: only major networks need to be advertised; even without “no auto-summary” command the network still works correctly. But in the exam the sim is just a flash based simulator so we should use two above commands, just
for sure. But after finishing the configuration, we can use “show run” command to verify, only the summarized network 190.200.0.0 is shown.
6000+ Exam Q&As
6000+ Free Demo
98% Pass Rate
100% Money Back Guarantee
365 Days Free Update
5 Years Working Experience
[100% Pass Pass4itsure 300-115 PDF Dumps Version From Google Drive]: https://drive.google.com/open?id=0BwxjZr-ZDwwWLW41Sk5QSDdPTFU
[100% Pass Pass4itsure 300-135 PDF Dumps Version From Google Drive]: https://drive.google.com/open?id=0BwxjZr-ZDwwWVjNzVmpXTDBzU00
What if I don’t pass the exam? How do I claim Refund?
Any Pass4itsure.com user who fails the corresponding exam has 30 days from the date of purchase of 300-115 dumps exam on Pass4itsure.com for a full refund. We can accept and arrange a full refund requests only if your score report or any relevant filed be confirmed.
This preparation guide is subject to change at any time without prior notice and at the sole discretion of Cisco. Pass4itsure Cisco exams might include adaptive testing technology and simulation items. Cisco does not identify the format in which exams are presented. Please use this preparation guide to prepare for the pass4itsure 300-115 dumps exam, regardless of its format. To help you prepare for this exam, Pass4itsure Cisco recommends that you have hands-on experience with the product and that you use the specified training resources. These training resources do not necessarily cover all topics listed in the “skills measured” section.
I believe that people want to have good prospects of career whatever industry they work in. Of course, there is no exception in the competitive IT industry. IT Professionals working in the IT area also want to have good opportunities for promotion of job and salary. A lot of IT professional know that pass4itsure 300-115 dumps exam exam tests can help you meet these aspirations. Pass4itsure is a website which help you successfully pass Cisco 300-115 dumps.
Useful Pass4itsure Cisco 300-115 Dumps Exam, Real Cisco 300-115 Dumps Vce Files Will Be More Popular, We Help You Pass Implementing Cisco IP Switched Networks.
Pass4itsure Promo Code 15% Off
